Free shipping on orders of $150 or more. Order online only. 40 lbs or less (Other conditions may apply).

Subscribe to our newsletter and receive $10 off your first order over $150.

Up to 35% off 180 tools in stock. See the deals

Nailers and Staplers

(46 products)

Nailers and staplers for finishing, framing, roofing and upholstery work. Pneumatic and cordless 20V and 18V models from DeWalt, Makita, Milwaukee and Metabo HPT.
View as

Our recommendations

Similar Categories

How to choose the right nailer or stapler for your project

Pneumatic or cordless nailer: which technology to choose

Pneumatic nailers operate between 70 and 120 PSI via a compressor, delivering a firing rate of 4 to 6 nails per second at a reduced cost per fastener. DeWalt 20V MAX and Makita 18V LXT models eliminate the air hose for total jobsite mobility.

The choice depends on daily work volume. Pneumatic tools suit continuous production in workshops or large-scale framing. Cordless nailers excel for overhead work, interior renovations, and sites without compressor access.

Understanding gauges: 16 GA, 18 GA, and 23 GA

16-gauge (1.6 mm) drives nails from 25 to 64 mm for thick moldings and door frames. 18-gauge (1.0 mm) suits light finish work, baseboards, and trim without splitting the wood. 23-gauge (0.6 mm) fires nearly invisible micro-pins for decorative moldings.

Staplers in 16 and 18 gauge fasten panels, upholstery, and subfloors with lateral holding power superior to nails. The choice between nail and staple depends on the resistance needed: pull-out (nail) or shear on thin materials (staple).

Framing and roofing nailers for heavy-duty work

Framing nailers drive nails from 51 to 89 mm (2 to 3-1/2 inches) in angled strips at 21 or 30 degrees. The DeWalt DCN930 cordless 20V and Metabo HPT NR90ADS1 pneumatic are among the top choices for dimensional lumber framing across Canada.

Coil roofing nailers accept galvanized nails from 19 to 45 mm for shingles and membrane. Firing at 4 to 6 nails per second at 80 PSI, these tools reduce fatigue during installation on large angled surfaces.

Professional staplers: narrow crown and wide crown

Narrow-crown staplers (18-gauge, 6 mm width) fasten moldings and plywood panels without leaving a visible mark. Wide-crown staplers (16-gauge, 25 mm width) assemble crates, lattice, and soft materials like upholstery fabric.

Milwaukee M18 FUEL and DeWalt 20V MAX XR offer cordless staplers capable of 1,000 to 1,500 staples per 5Ah battery charge. For pneumatic models, recommended pressure ranges from 70 to 100 PSI depending on the material thickness to penetrate.
Industrial Air Compressors Pneumatic Tools DeWalt 20V Batteries DeWalt 20V MAX Tools Makita LXT 18V Tools Milwaukee M18 Tools Power Tools DeWalt Saws Pneumatic Hoses and Reels Power Tool Accessories DeWalt Chargers DeWalt Nailers

Your nailer and stapler questions answered

What is the difference between a nailer and a stapler?

A nailer drives nails (brad, finish, or framing) that offer superior pull-out resistance. A stapler drives U-shaped staples that resist shear forces better and cover a wider contact area on thin materials.

In practice, nailers are best for structural assembly and trim work, while staplers excel at upholstery, fabric attachment, subflooring, and thin panels. Many 2-in-1 models combine both functions in a single tool.

What gauge nailer should I use for finish work?

An 18-gauge nailer (1/2 to 2-inch nails) works best for baseboards, thin trim, and moldings without splitting risk. A 16-gauge nailer (1 to 2-1/2 inch nails) provides more holding power for thick crown molding, door frames, and shelving.

For ultra-delicate work like decorative moldings or cabinet returns, a 23-gauge pinner (headless micro-nails) leaves a nearly invisible hole that requires no filling.

Pneumatic or cordless nailer: which is more powerful?

At equal gauge, driving power is comparable. Pneumatic nailers draw from a compressor set between 70 and 120 PSI, delivering consistent pressure even at high firing rates.

Cordless nailers like the DeWalt 20V MAX and Makita 18V LXT use a brushless motor to compress air internally. The real difference is sustained rate: pneumatic tools fire indefinitely, while cordless models depend on battery life (800 to 1,200 nails per 5Ah charge).

What PSI should I set my compressor to for a nailer?

Most finish nailers (16-18 gauge) operate between 70 and 100 PSI. Framing and roofing nailers typically require 80 to 120 PSI to drive 2 to 3-1/2 inch nails into dimensional lumber.

Always check the recommended PSI range on the tool's spec sheet. A minimum 6-gallon compressor delivering 2.5 to 4 CFM at 90 PSI is sufficient to power a single nailer in continuous use.

What nailer do I need for hardwood flooring?

Installing 3/4-inch solid hardwood requires a pneumatic flooring nailer that drives 2-inch L-cleats (16-gauge) or 2-inch staples at a 45-degree angle into the tongue of each plank.

For thinner engineered flooring (3/8 to 1/2 inch), a narrow-crown 18-gauge stapler with 1 to 1-1/2 inch staples prevents blow-through. Recommended pressure sits between 70 and 80 PSI to avoid damaging the planks.

What professional nailer brands are available?

The catalog includes DeWalt (20V MAX platform, the largest cordless lineup), Makita (18V LXT platform), Milwaukee (M18 FUEL), Metabo HPT (formerly Hitachi, known for pneumatic finish nailers), and Bostitch (framing and roofing).

All these brands share battery platforms compatible with their other cordless power tools, allowing professionals across Canada to consolidate their battery inventory on a single jobsite.

CAN'T FIND THE PRODUCT YOU'RE LOOKING FOR?

CONTACT US

Compare /8