Free shipping on orders of $150 or more. Order online only. 40 lbs or less (Other conditions may apply).

Subscribe to our newsletter and receive $10 off your first order over $150.

Up to 35% off 180 tools in stock. See the deals

Tools to Change Your Winter Tires Yourself

Les outils pour changer ses pneus d'hiver soi-même

Agence Elevex |

Winter tires are mandatory in Quebec from December 1 to March 15. To install them yourself, you need tools to lift the car, loosen the nuts, retighten them to the right torque and check the pressure.

Below, we have gathered the tools we sell at Equipement Polar for each step, with their price and what they offer. The exact torque for your wheel nuts is always in the vehicle's manual.

Our Quick Picks

Winter Tire Dates in Quebec

For most vehicles registered in Quebec, winter tires are mandatory from December 1 to March 15. The tire must carry the snowflake-on-a-mountain symbol or be studded, according to the Government of Quebec website.

Installing your wheels in October or November leaves time to check your equipment before the first snow. The symbol is on the tire sidewall.

Prepare the Garage Before You Start

A few ten-minute checks prevent most bad surprises. Do them before taking out the first tool.

  • The vehicle manual: it gives the lifting points, the vehicle weight, the wheel nut torque and the nut size.
  • The work surface: flat, hard and dry ground, such as a concrete slab or asphalt, with no slope.
  • Available space: enough room to set the wheels down and walk around the car.
  • Tool batteries: charged before you start, if you use a cordless impact wrench.
  • The winter wheels: symbol visible on the sidewall, tread in good condition and pressure up to date.
  • Locking lug nuts: if your wheels have them, keep the special key within reach before lifting the car.

The Essential Tools at a Glance

StepToolModel in our selectionPrice
SecureWheel chocksBraber 67.003.103$21.27
Loosen1/2 in. impact wrenchMilwaukee 2855-22R$560.60
LoosenMetric impact socketsJet 610338$149.00
Tighten1/2 in. torque wrenchDeWalt DWMT75462$170.29
CheckPressure gaugeTopring 63.711$60.87

See the full tools to change tires collection at Equipement Polar.

Lifting the Car Safely

A jack lifts the car, it does not hold it up. As soon as the wheel is off the ground, slide a jack stand under the support point specified by the manufacturer.

Work on flat, hard ground with the parking brake set and chocks behind the wheels that stay on the ground. The capacity of the jack and the jack stands must exceed the vehicle weight shown in the manual.

Choosing the Capacity of the Jack and Jack Stands

The vehicle weight is in the owner's manual. The equipment you choose must always exceed it, otherwise it works at its limit.

EquipmentCapacityFor which vehiclePrice
Strongarm 0304162 1/2-ton jack, 3-ton jack standsCars and light vehicles$378.13
DeWalt DXALT830026XHB3 tonsLow cars, SUVs and light trucks$299.00
Sunex 6 tons6 tons per pair of jack standsPickups and heavy vehicles$233.87
Jet 140401 bottle jack8 tonsHeavy vehicles$117.81
Strongarm 314A bottle jack12 tons, height of 7 to 13 in.Heavy vehicles$119.17

Bottle jacks offer a large capacity for their price. Before choosing one, compare its lifting height with the height of your vehicle's support point.

DeWalt DXALT830026XHB Hydraulic Jack, 3 Tons

For low cars and SUVs

DeWalt DXALT830026XHB 3-ton hydraulic jack for changing winter tires
Capacity3 tons
Entry height3-1/8 in. (79 mm)
Maximum lift23 in. (584 mm) with the adapter
PumpDual piston

Its low profile slides under sports cars, and the included height adapter lets it reach SUVs and light trucks. The slow-release valve controls the lowering.

It is sold without jack stands. You therefore need to add a pair, such as the Sunex stands below.

Price: $299.00

View the DeWalt 3-ton jack →

Sunex 6-Ton Jack Stands (Sold as a Pair)

For pickups and heavy vehicles

Pair of Sunex 6-ton jack stands to support a vehicle when changing winter tires
Capacity6 tons
Height15-3/4 to 24 in.
Weight32.5 lb

The 15-3/4 to 24 inch adjustment range suits raised vehicles. They are sold as a pair and combine with any jack in the selection.

Price: $233.87

View the Sunex 6-ton jack stands →

Braber 4 kg Rubber Wheel Chock (67.003.103)

The most affordable on the list

Braber 4 kg rubber wheel chock for changing winter tires

The 4 kg rubber chock goes in front of or behind a wheel that stays on the ground. Plan on two, one on each side of the wheel.

Price: $21.27 each

View the Braber wheel chock →

Loosening the Nuts with an Impact Wrench

A 1/2 in. impact wrench loosens in seconds nuts that would take several minutes to force by hand. Three criteria guide the choice.

  • Breakaway torque: it must handle a nut tightened at the factory or rusted after a year on the car.
  • Battery platform: a Milwaukee M18, DeWalt 20V MAX or Makita XGT 40V wrench runs on the batteries of the tools you already have.
  • Format: a compact wrench fits in tight wheel wells, a longer wrench offers more torque.

A model with 250 ft-lb of breakaway torque is enough to loosen the wheel nuts of a passenger car in good condition. A seized nut or a larger vehicle calls for a more powerful model.

The Three 1/2 in. Impact Wrenches at a Glance

ModelPlatformStated loosening torqueBatteryPrice
Makita TW007GZXGT 40V810 ft-lbSold without battery$419.00
DeWalt DCF961B20V MAX XRUp to 1,750 ft-lbTool only$448.00

Makita TW007GZ, 1/2 in. Brushless XGT 40V Impact Wrench (Tool Only)

For large nuts and pickups

Makita TW007GZ XGT 40V 1/2 in. impact wrench for winter tires
Maximum fastening torque560 ft-lb (760 Nm)
Loosening torque810 ft-lb (1,100 Nm)
Length6-11/16 in. (170 mm)
Weight4.5 lb (2.0 kg)

Four power levels and three forward and reverse auto shut-off modes help prevent over-tightening. It requires an XGT 40V battery, sold separately.

Its 4.5 lb weight and 170 mm length make it easy to handle despite its high torque.

Price: $419.00

View the Makita TW007GZ →

DeWalt DCF961B, 20V MAX XR 1/2 in. Impact Wrench (Tool Only)

The highest loosening torque in the selection

DeWalt DCF961B 20V MAX XR 1/2 in. impact wrench for loosening winter tire nuts
Loosening torqueUp to 1,750 ft-lb
Anvil1/2 in., hog ring type
Modes3 speeds and Precision Wrench
Weight7.65 lb (tool only)

The Precision Wrench mode gives more control to avoid over-tightening and ejecting the fastener when unscrewing. Battery and charger are sold separately.

Its 7.65 lb weight is higher than the Makita, which weighs 4.5 lb.

Price: $448.00

View the DeWalt DCF961B →

Impact Sockets

An impact wrench needs impact sockets made of chrome-molybdenum steel, thicker than ordinary sockets. 17, 19 and 21 mm wheel nuts are common, so check your vehicle's size before buying.

Jet 610338 1/2 in. Metric Impact Socket Set, 22 Pieces

The most complete metric set on the list

Drive1/2 in.
Pieces22, metric, 6-point
SteelChrome-molybdenum SAE 4140

The Torque Drive sockets grip the flats of the nut to limit rounding of the corners. The molded case keeps the set organized.

Price: $149.00

View the Jet 610338 set →

Jet 610310 1/2 in. Metric Long Impact Socket Set, 12 Pieces

For nuts recessed in the rim

Drive1/2 in.
Pieces12, extra-long, metric
SteelChrome-molybdenum SAE 4140

The extra-long sockets reach deep nuts, common on alloy rims. They use the same Torque Drive sockets as the 22-piece set.

Price: $106.00

View the Jet 610310 set →

Some older vehicles use inch-size nuts. In that case, the Jet 610328 19-piece SAE set at $120.94 covers the range.

Why You Do Not Tighten with the Impact Wrench

The impact wrench is for loosening. When tightening, it can exceed the specified torque without you noticing, which damages the studs.

So thread the nuts by hand, then finish with a torque wrench set to the value in the manual.

Tightening to the Right Torque with a Torque Wrench

The torque wrench is the tool that prevents both a loose wheel and an over-tightened nut. Tighten in a star pattern, or criss-cross when the wheel has four nuts, in two passes.

  • First pass: at about half of the manual's value.
  • Second pass: at the full value, in the same order.

After about 50 km, recheck the torque, as Continental recommends. All the wrenches in the selection have a 1/2 in. drive, the most common for wheel nuts.

Jet 718912 Torque Wrench, 1/2 in., 50 to 250 ft-lb

Supplied with its calibration certificate

Jet 718912 1/2 in. 50 to 250 ft-lb torque wrench for tightening wheel nuts
Range50 to 250 ft-lb
Accuracy+/- 4%, factory calibrated with certificate
StandardsISO 6789 and ANSI
Ratchet24 teeth, reversible

An audible click and a noticeable jolt signal that the setting is reached. A molded case protects the wrench between uses.

Price: $270.00

View the Jet 718912 wrench →

DeWalt DWMT17060 1/2 in. Digital Torque Wrench

Backlit display and unit conversion

DeWalt DWMT17060 1/2 in. digital torque wrench for winter tires
Range50 to 250 ft-lb
DisplayBacklit LED
UnitsFoot-pounds, inch-pounds, Nm
Supplied with2 batteries, case, manual

The display shows the torque continuously and a button changes the unit. It is the wrench in the selection for those who want to read the value rather than count clicks.

Price: $295.00

View the DeWalt DWMT17060 →

To compare more ranges and wrench types, read our ranking of the 6 best torque wrenches in Canada, or browse the torque wrenches collection.

Checking Tire Pressure

A winter wheel coming out of storage has often lost pressure. Measure it cold, that is, with the vehicle parked for at least three hours or driven less than 2 km.

Topring 63.711 Inflation Gauge and Gun (0 to 90 PSI)

Accurate for vehicles with a TPMS

Topring 63.711 inflation gauge and gun for measuring winter tire pressure
Range0 to 90 PSI
Graduation1 PSI
FunctionsInflate, deflate, measure
Hose38 cm

The 60 mm gauge is protected by a rubber sleeve. It allows precise inflation that avoids pressure warning light errors.

Price: $60.87

View the Topring 63.711 gauge →

Makita DMP181Z 18V Cordless Inflator (Tool Only)

The standalone inflator for the garage

Makita DMP181Z 18V cordless inflator for winter tires
DisplayBacklit digital gauge
Unitspsi, kPa or bar
Shut-offAutomatic at the set pressure
Hose25-1/2 in.

It stops by itself at the chosen pressure and remembers the setting. An air release function brings the pressure back down in case of overinflation.

Price: $209.00

View the Makita DMP181Z inflator →

Special Cases

Four situations call for a little more attention than the standard case of a passenger car.

SUVs and Pickups

Their higher weight requires a jack and jack stands of greater capacity. The DeWalt 3-ton jack with its 23 inches of lift using the adapter, or the Sunex 6-ton jack stands, are designed for these vehicles.

Alloy Rims

The nuts are often recessed in the rim, which calls for long sockets such as the Jet 610310 set. Seat the socket straight on the nut before operating the wrench.

Vehicles with a TPMS

A warning light comes on when the pressure is set incorrectly. An accurate gauge, such as the Topring 63.711, helps you inflate to the exact value and avoid error messages.

Locking Lug Nuts

A locking nut is loosened with its dedicated key. Find it before lifting the vehicle, because it is harder to look for it once the car is in the air.

What You Do Not Need

Our collection also includes tire irons, such as the Ken-Tool T47B at $370.75. They are used to take the tire off the rim, an operation that also requires balancing.

If you swap complete wheels, with winter tires already mounted on their rims, you can skip this step.

Other Models in the Collection

The selection above covers the essentials. Other models in the collection fit depending on budget and battery platform.

What Budget to Plan For

To equip yourself from scratch with the models in this selection, the total is $1,361.43 before taxes. This calculation counts the Strongarm kit, two chocks, the Milwaukee wrench with its batteries, the Jet socket set, the DeWalt torque wrench and the Topring gauge.

ItemPrice
Strongarm 030416 jack and jack stands$378.13
2 Braber wheel chocks$42.54
Milwaukee 2855-22R impact wrench (batteries included)$560.60
Jet 610338 metric impact sockets$149.00
DeWalt DWMT75462 torque wrench$170.29
Topring 63.711 gauge$60.87

If you already own a cordless impact wrench, the budget drops by more than $500. M18, 20V MAX and XGT batteries are shared between tools of the same brand.

The 8-Step Method

  1. Secure the vehicle. Flat, hard ground, parking brake set, chocks against the wheels that stay on the ground.
  2. Loosen the nuts. A small loosening with the wheel still on the ground, so it does not turn.
  3. Lift the vehicle. The jack goes at the lifting point shown in the manual.
  4. Set the jack stands. Lower the load onto them before any other handling.
  5. Remove the wheel. The nuts come off with the impact wrench or by hand.
  6. Mount the winter wheel. Thread all the nuts by hand so they start straight.
  7. Tighten to torque. Lower the vehicle, then tighten in a star pattern with the torque wrench, in two passes.
  8. Recheck after 50 km. Tightening torque and cold pressure.

Mistakes to Avoid

Most problems come from a shortcut taken at the wrong time. Each mistake on the list has a right way to do it.

  • Working under a vehicle supported by a jack alone: a jack lifts, jack stands hold the load.
  • Tightening the nuts with an impact wrench: always finish with a torque wrench, at the manual's value.
  • Tightening in a circle: the star pattern spreads the pressure, or the criss-cross pattern for four nuts.
  • Skipping the second pass: a first pass at half the torque, then a second at the full value.
  • Skipping the recheck: a torque check after about 50 km is part of the method.
  • Lifting at an unspecified point: the manual shows the manufacturer's lifting and support points.

At the End of the Season

The same method applies in the spring, in reverse. The same tools are used, and you still need to check the pressure of the summer tires before mounting them.

Need Help Getting Equipped?

Our team can advise you based on your vehicle and your battery platform. Free shipping in Canada on orders of $150 or more.

View the tire changing tools Contact our experts

FAQ on Changing Winter Tires

When should I install winter tires in Quebec?+
Winter tires are mandatory from December 1 to March 15 for most vehicles registered in Quebec. The tire must carry the snowflake-on-a-mountain symbol or be studded.
What torque should I use for wheel lug nuts?+
The value depends on the vehicle and is in the owner's manual. Set the torque wrench to that value and do not rely on a generic number.
Can I tighten lug nuts with an impact wrench?+
An impact wrench is fine for loosening. For final tightening it can exceed the specified torque without you noticing, so always finish with a torque wrench.
Is a jack enough to change a wheel?+
No. A jack lifts the car but does not hold it. As soon as the wheel is off the ground, place jack stands under the vehicle's support points.
What socket size do I need for lug nuts?+
It depends on the vehicle. 17, 19 and 21 mm nuts are common, but check the size on your vehicle before buying. Some older models use inch sizes, covered by the Jet 610328 SAE set.
Should I retighten the nuts after a few kilometres?+
Yes. After about 50 kilometres, check the torque and retighten to the same value if needed.
What tools do I need to change a tire on its rim?+
You need a tire changer or tire irons, then wheel balancing. Most people have their winter tires mounted on dedicated rims and then swap the complete wheels.
How do I know if my vehicle is too heavy for my jack?+
The vehicle weight is in the owner's manual. The capacity of both the jack and the jack stands must exceed it.
What pressure should winter tires be inflated to?+
The value is in the manual and on the vehicle's label. Measure it cold: vehicle parked for at least three hours or driven less than 2 km.
Do I need to balance the wheels to swap them?+
If the tires are already mounted and balanced on their rims, the balance remains valid. Balancing is needed when a tire is mounted on a rim.